Industrial Centrifugal Fan
Tunnel Fan & Metro Fan
(Gas Heating) Make-up Air Unit
Infrared Radiant Heaters
Mixed Flow Fan
Axial Flow Fan
Inducing Fan
Kitchen Fume Extractor Fan
Cabinet Fans
Inline Centrifugal Fan
Roof Fan
Wall Mounted Fan
OEM Customization
Intelligent Control

Contact Us

Tel:+86 21-3918 5688 EXT-6896
E-mail:[email protected]


Backward Curved SWSI Centrifugal Fan - Wheel Type O-YFBCSO

● Wheel Specification: 400~1,400
● Installation: floor-mounted
● Volume range: 1,490~109,500 m³/h
● Static pressure range: 475~109,00 Pa
● Advanced backward curved wheel-Type O design,high efficiency.
● CFD flow optimization repeatedly,high-efficiency range and non-overload.
● Balance quality grade up to G4.0 (AMCA 204).
● Wheel extractable design for easy maintenance.
● Fully welded, high strength and leak-tightness.
● Various transmission ways for flexible selection and allocation.
● Completely planned series energy-saving products.

Inquiry Online

Optimized design
-- The fan adopts advanced technology. Design of backward curved centrifugal wheel is optimized by means of CFD hydro-field simulating. The design is more accordant with the aerodynamic characteristics, high efficiency, and stable airflow

Advanced process
-- Steel laser cutting, precise positioning jig and all-welded technique are adopted for the blade to ensure smoothness of the margin of the blade. The welding angle is accurate, the whole blade is with strong strength, and the stress is evenly distributed during long-time high-speed operation. The operation is stable and reliable

High balancing level
-- Each wheel is subjected to dynamic balance test. We insist to the balancing level of G4.0 (Typical products are balanced to G6.3 only). Long-term quiet and stable running of the fan is ensured fundamentally

High-efficiency range

-- The wheel has a stable and smooth aerodynamic performance curve and owns a wide range of high efficiency working area which can efficiently avoid fan performance decrease caused by the deviation of the working point


-- The series wheel exist a peak value of shaft power, when the motor is selected according to the power combined with the margin factor of motor power, the fan shaft power will not exceed the motor rated power no matter on which operation point of the stable working range the is running, then the clients can use it at ease


High reliability
-- Efficient backward curved centrifugal wheel with high efficiency wide and non-overload characteristics to ensure operation more reliably and safely.
-- To be adopted FEA-aided design for enhancing the reliability of structure.
-- Scroll and wheel with high strength and no leakage characteristics are all-steel continuous welded to improve operation safely.
-- Each wheel is balanced, , We insist to the balancing level of G4.0 (AMCA 204).
-- To be vibration tested before the fan leave the factory to achieve the requirements of long-term stable and reliable operation .
-- To be configured shields and adopted bright warning color of the drive unit to ensure the personal safety of customer.
-- Fan shaft is subjected to finish turning & hardening and tempering. Maximum load surpasses 35% of limit speed to ensure the long-term continuous operation of the security .
-- Bearing seal can be lubricated. Service life more than L10:80000 hours to ensure the reliability of long-term continuous operation.

High efficiency

-- Backward curved centrifugal wheel with high efficiency wide to avoid performance degradation caused by changes in working point.
-- Venturi inlet matched front disc precisely to avoid turbulent flow and air leakage, so that the air flow more smoothly to improve aerodynamic performance.
-- Optimized design repeatedly of CFD flow field simulation to ensure aerodynamic performance complied with the flow field characteristics

-- Flexible allocation of multi-drive type .
-- Standard accessories for normal use.
-- Accessories completely to meet all kinds of application requirements.


Naming Convention:

Tech Spec

YFBCSO Technical Specification

Fan Type
The fan shall be single inlet with steel backward curved centrifugal wheel. The drive type shall be direct drive, coupling drive and belt drive. Structure of the fan shall allow convenient withdrawal of the wheel for maintenance and cleaning.

Quality Standards
The fan shall be tested in accordance with AMCA Standard 210 and 300. The manufacturer must own the production license for industrial products and ISO9001 quality system authentication.

The wheel shall be steel backward curved centrifugal and fully welded. The wheel shall be statically and dynamically balanced to level G4.0 in accordance with AMCA204. When the wheel is operating at the highest allowable speed, the volume shall be stable and the noise shall be low. Wheel features shall be able to avoid performance downgrade resulting from sliding of the working points. Wheel material shall be Q235 for the temperature under 60 degrees centigrade, Q345 for the temperature between 61 and 250 degrees centigrade, and 304SS for the temperature between 251 and 450 degrees centigrade to ensure the wheel’s strength and no creep deformation in high temperature and high speed running in working condition.

Fan Housing
The fan housing shall be steel, the thickness and strength shall be adequate to support fan max running weight. The volute shall be continuously welded and equipped with access door for removing possible foreign objects entered into the scroll.

Fan inlet shall be aerodynamic design round curved section to smoothly transit the air to the wheel cone, it will have good commutate effect to effectively reduce turbulence, improve fan efficiency and reduce noise.

Fan surface shall be polished and cleaned up to remove particulates, welding slag, burrs, sharp edge, iron, oil, then epoxy coating or high temperature coating for high temperature environments use, fan surface shall be free of sags, wrinkle, blisters, exposed metal or peeling after coating. It shall be no corrosion and rust at least 10 years in allowable working condition.

Transmission Device (Only for belt drive and coupling drive type)
Fan shaft shall be heat treated through soaking furnace to the hardness level between  251 and 450 degrees centigrade, and the maximum load is 35% higher than that of the max RPM, the shaft shall be furnished with cover. The material of shaft shall be 40Cr when the working condition temperature under 250 degrees centigrade, and shall be 35CrMo when the working condition temperature between 251 and 450 degrees centigrade. The support structures shall be whole drum-type bearing box. The bearings shall be selected for a minimum (L-10) life in excess of 80,000 hours at maximum cataloged operating speed. The bearing lubrication shall be adopted thin oil between N32 and N46, the amount of lubrication oil shall be according to the requirements of the oil level mark. The Bearing box shall be equipped with water cooling device for choosing whether or not through water according to the conditions in the field for the temperature between 61 and 250 degrees centigrade. The Bearing box shall be equipped with water duct and through water for the temperature up to 250 degrees centigrade, the water consumption increased as the temperature varies, generally can be considered as 0.3~1m3/h. The pulley shall be constructed of cast-iron; Fan pulleys shall be sized for a minimum of 130% of driving power. The pulley and belt shall be furnished with cover. The coupling shall be elastic coupling with cover, too. Its safety of conveying power and torsion shall meet the design requirements.

Motor shall be carefully matched to the fan load, IP54, and insulation class F. Motor bearings shall be lubricant ball type. Motor and drives shall be out of the air stream to avoid grease or dirt accumulation.

Explosion-proof Structure (Only for explosion-proof type)
Fan shall conform to Spark C explosion-proof structure according to AMCA99 Standard. The inlet shall mount copper ring and the motor shall adopt explosion-proof type. The whole fan should own CNEX certification and the manufacturer must own the production license for anti-explosion electric products.

Permanently fixed aluminum nameplate shall be fixed on fan body clearly display fan mark, product model and serial number (i.e.: unique ID for each fan), so that the customer can use this number to find out the parts used.

Acceptable Manufacturers

Qualified suppliers shall have an AAA credit rating. Providing INFINAIR or similar products, with their design based on YFBCSO models of INFINAIR.



Online Message